642-883 Exam Questions

  • OFFER Free Cisco 642-883 PDF and VCE Exam Dumps (51-60)

    QUESTION 51
    Refer to the Cisco IOS show command output shown in the exhibit. Which of the following statements is correct?

    image

    A.    The best path to 10.2.10.1/32 was chosen because of the AS path.
    B.    The best path to 10.2.10.1/32 was chosen because of the weight.
    C.    The best path to 10.2.10.1/32 was chosen because of the local preference.
    D.    The best path to 10.2.10.1/32 was chosen because of the MED.
    E.    The best path to 10.2.10.1/32 was chosen because of the route origin.

    Answer: B

    (more…)

  • OFFER Free Cisco 642-883 PDF and VCE Exam Dumps (31-40)

    QUESTION 31
    Referring to the partial Cisco IOS-XR BGP configuration exhibit, when trying to commit this configuration, the following error is displayed:
    % Failed to commit one or more configuration items during a pseudo-atomic operation. All changes made have been reverted. Please issue ‘show configuration failed’ from this session to view the errors.

    image
    What is wrong with the configuration?

    A.    IPv6 unicast routing has not been enabled globally using the ipv6 unicast-routing command
    B.    The configuration is missing the required network command
    C.    The update-source loopback 0 commands must be configured under the respective neighbor
    address-family
    D.    The configuration is missing the address-family ipv4 unicast and address-family ipv6 unicast
    commands under router bgp 65111

    Answer: D

    (more…)

  • OFFER Free Cisco 642-883 PDF and VCE Exam Dumps (11-20)

    QUESTION 11
    Refer to the topology diagram in the exhibit. Which IS-IS feature could be implemented so that the return path for the packets from router Y in area 49.00AA to router X in area 49.00BB will use the more optimal path?

    image

    A.    Enable route leaking to pass Level 2 information into the Level 1 routers.
    B.    Change the area 49.00AA type from a stub area to a regular area.
    C.    Change the IS-IS administrative distance on router Y in area 49.00AA.
    D.    Change the IS-IS metric type from narrow to wide on all IS-IS routers.

    Answer: A

    (more…)

  • OFFER Free Cisco 642-883 PDF and VCE Exam Dumps (1-10)

    QUESTION 1
    Refer to the OSPF command exhibit. Which effect does the no-summary command option have?

    image

    A.    It will cause area 1 to be able to receive non-summarized inter-area routes.
    B.    It will cause area 1 to not receive any inter-area routes and will use a default route to reach
    networks in other areas.
    C.    It will cause area 1 to not receive any external routes and will use a default route to reach the
    external networks.
    D.    It will convert the NSSA area into a NSSA totally stubby area.
    E.    It will convert the stubby area into a NSSA.
    F.    It will disable OSPF auto-summary.

    Answer: B

    QUESTION 2
    When troubleshooting OSPF neighbor errors, which three verification steps should be considered? (Choose three.)

    A.    Verify if neighboring OSPF interfaces are configured in the same area.
    B.    Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
    C.    Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
    D.    Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
    E.    Verify if neighboring OSPF interfaces are configured with the same area type.

    Answer: ADE

    QUESTION 3
    On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?

    A.    interface gi0/0/0/0
    ip address 10.1.1.1 255.255.255.0
    !
    router ospf 1
    network 10.1.1.1 0.0.0.0 area 0
    B.    interface gi0/0/0/0
    ip address 10.1.1.1 255.255.255.0
    !
    router ospf 1
    network 10.1.1.1 255.255.255.255 area 0
    C.    router ospf 1
    area 0
    interface GigabitEthernet0/0/0/1
    D.    interface gi0/0/0/0
    ip address 10.1.1.1 255.255.255.0
    ip ospf 1 area 0
    E.    router ospf 1
    address-family ipv4 unicast
    interface GigabitEthernet0/0/0/1 area 0
    F.    router ospf 1
    address-family ipv4 unicast
    interface GigabitEthernet0/0/0/1
    area 0

    Answer: C

    QUESTION 4
    Which three statements are true regarding the OSPF router ID? (Choose three.)

    A.    The OSPF routing process chooses a router ID for itself when it starts up.
    B.    The router-id command is the preferred procedure to set the router ID.
    C.    If a loopback interface is configured, its address will always be preferred as the router ID over any
    other methods.
    D.    After the router ID is set, it does not change, even if the interface that the router is using for the router
    ID goes down. The router ID changes only if the router reloads or if the OSPF routing process restarts.
    E.    In OSPF version 3, the OSPF router ID uses a 128-bit number.

    Answer: ABD

    QUESTION 5
    Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)

    A.    to connect an OSPF non-backbone area to area 0 through another non-backbone area
    B.    to connect an NSSA area to an external routing domain
    C.    to connect two parts of a partitioned backbone area through a non-backbone area
    D.    to enable route leaking from Level 2 into Level 1
    E.    to enable route leaking from Level 1 into Level 2
    F.    to enable OSPF traffic engineering

    Answer: AC

    QUESTION 6
    What is function of the RP/0/RSP0/CPU0:PE1(config-ospf)#distance Cisco IOS-XR command?

    A.    To modify the administrative distance of the OSPF routes
    B.    To modify the default seed metric of the OSPF external routes
    C.    To modify the OSPF default reference bandwidth
    D.    To modify the OSPF cost

    Answer: A

    QUESTION 7
    Which four statements are correct regarding IS-IS operations? (Choose four.)

    A.    By default, Level 1 routers within an IS-IS area do not carry any routing information external to
    the area to which they belong. They use a default route to exit the area.
    B.    Summarization should be configured on the Level 2 routers, which injects the Level 2 routes
    into Level 1.
    C.    IS-IS supports “route leaking” in which selected Level 2 routes can be advertised by a Level 1/Level 2
    router into Level 1.
    D.    The IS-IS backbone is a contiguous collection of Level 1 capable routers, each of which can be in
    a different area.
    E.    With IS-IS, an individual router is in only one area, and the border between areas is on the link that
    connects two routers that are in different areas.
    F.    Cisco IOS XR Software supports multitopology for IPv6 IS-IS unless single topology is explicitly
    configured in IPv6 address-family configuration mode.

    Answer: ACEF

    QUESTION 8
    When configuring IPv4 and IPv6 IS-IS routing on Cisco IOS XR routers, which three statements are correct? (Choose three.)

    A.    By default, a single SPF is used for both IPv4 and IPv6, so the IPv4 and IPv6 topology should
    be the same.
    B.    By default, the IS-IS router type is Level 1 and Level 2.
    C.    All IS-IS routers within the same IS-IS area must be configured with the same IS-IS routing process
    instance ID.
    D.    By default, metric-style narrow is used.
    E.    By default, the IS-IS interface circuit type is Level 1 and Level 2.
    F.    The area IS-IS address-family configuration command is used to specify the IS-IS area address.

    Answer: BDE

    QUESTION 9
    Refer to the PE1 router routing table output exhibit. What is causing the i su 10.1.10.0/24 [115/30] via 0.0.0.0, 00:40:34, Null0 entry on the PE1 router routing table?

    image

    A.    The PE1 router is receiving the 10.1.10.0/24 summary route from the upstream L1/L2 IS-IS router.
    B.    The PE1 router has been configured to summarize the 10.1.10.x/32 IS-IS routes to 10.1.10.0/24.
    C.    The 10.1.10.0/24 has been suppressed because IS-IS auto-summary has been disabled on the
    PE1 router.
    D.    The 10.1.10.0/24 has been suppressed because of a route policy configuration on the PE1 router.
    E.    The 10.1.10.0/24 has been suppressed because the more specific 10.1.10.x/32 IS-IS routes have
    been configured to leak into the IS-IS non-backbone area.

    Answer: B

    QUESTION 10
    In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?

    A.    ASBR on a normal OSPF area
    B.    ASBR on NSSA
    C.    ABR on totally stubby OSPF area
    D.    ABR on stubby OSPF area
    E.    ABR on a normal OSPF area

    Answer: C

    If you want to pass Cisco 642-883 successfully, donot missing to read latest lead2pass Cisco 642-883 practice tests.
    If you can master all lead2pass questions you will able to pass 100% guaranteed.

    http://www.lead2pass.com/642-883.html